Nalgene® Hydration Systems
Nalgene® Hydration Systems
Nalgene® has built an entire line of portable hydration systems around a single good idea: containers that let you experience the taste of their contents, not the flavor of their plastic. Outdoor enthusiasts use Nalgene® products for everything from casual outings to endurance-testing tours and even home storage use. With a reputation for high-quality, taste-free products, Nalgene® hydration systems are the premier choice for use in all of The North Face® hydration packs.
TPE Reservoir
Reliably tough and beautifully versatile for the die-hard adventurer.
- Special TPE polymer is virtually taste-free
- Strong construction stands up to wear and tear while doing away with annoying crinkly noise
- One piece seamless tubular design means less chance of leakage or tearing
Big Bore Opening
- Wide-mouth cap allows hassle-free access to water dispensers and ice cubes
- 63 mm thread matches the standard for most water purifiers and filtration devices
Reservoir Care
Your new hydration system is made to last. To ensure long life, please follow the care and use instructions.
- Prior to each use, fill reservoir, tighten cap, then squeeze to ensure that the cap is sealed properly
- When freezing, fill reservoir no more than 3/4 full
- To clean, add 1 tsp. baking soda to 1 cup water. Shake, empty and rinse. Then add 1 tsp. lemon or lime juice to 1 cup water. Shake, empty, rinse and dry.
Reliably tough and beautifully versatile for the die-hard adventurer.
- Special TPE polymer is virtually taste-free
- Strong construction stands up to wear and tear while doing away with annoying crinkly noise
- One piece seamless tubular design means less chance of leakage or tearing
Big Bore Opening
- Wide-mouth cap allows hassle-free access to water dispensers and ice cubes
- 63 mm thread matches the standard for most water purifiers and filtration devices
Reservoir Care
Your new hydration system is made to last. To ensure long life, please follow the care and use instructions.
- Prior to each use, fill reservoir, tighten cap, then squeeze to ensure that the cap is sealed properly
- When freezing, fill reservoir no more than 3/4 full
- To clean, add 1 tsp. baking soda to 1 cup water. Shake, empty and rinse. Then add 1 tsp. lemon or lime juice to 1 cup water. Shake, empty, rinse and dry.
 |
Quick Connect HoseQuick connect hose assembly means easy-on, easy-off when you’re swapping out components or filling the bladder (not available on Bullhead). |
 |
Angled Bite Me™ Valve- Angled design with on/off switch- Superior flow rate for easy drinking - Leakproof construction keeps water where it needs to be - Easy to disassemble and clean - Angled design keeps a low profile and provides a better fit - Positive shut-off valve allows you to decide when and where your liquids are available |
Bite Me™ Valve Use
For maximum flow, bite sheath with front teeth only and draw fluid in. Biting too hard and/or using teeth or molars will reduce flow and may damage or break the valve. The Bite Me™ valve is not intended for use by small children.
Disassembly, Cleaning, and Reassembly for Bite Me™ Valve
Remove bite valve by pushing it off the end of the drink tube. Remove sheath by pushing it off the end of the stem. Clean and sanitize the parts by soaking the sheath and the bite valve in the open position, in a diluted bleach solution. Replace sheath and reassemble by pushing the bite valve fitting into the end of the drink tube until it stops. Wet the sheath, then push it over the stem until you feel it lock into place. To assure proper operating and maximum flow, the dome of the sealing disk should protrude slightly beyond the end of the soft sheath.
Insulation
Insulated hydration pocket helps to keep your beverage either hot or cold.
For maximum flow, bite sheath with front teeth only and draw fluid in. Biting too hard and/or using teeth or molars will reduce flow and may damage or break the valve. The Bite Me™ valve is not intended for use by small children.
Disassembly, Cleaning, and Reassembly for Bite Me™ Valve
Remove bite valve by pushing it off the end of the drink tube. Remove sheath by pushing it off the end of the stem. Clean and sanitize the parts by soaking the sheath and the bite valve in the open position, in a diluted bleach solution. Replace sheath and reassemble by pushing the bite valve fitting into the end of the drink tube until it stops. Wet the sheath, then push it over the stem until you feel it lock into place. To assure proper operating and maximum flow, the dome of the sealing disk should protrude slightly beyond the end of the soft sheath.
Insulation
Insulated hydration pocket helps to keep your beverage either hot or cold.
